Ryobi RLM4619SME Manual do Operador descarregar pdf (Página 10)

English

MAINTAINING THE SPARK PLUG

See figure 11.

The spark plug must be properly gapped and free of

deposits in order to ensure proper engine operation. To

check:

1. Remove spark plug boot.

2. Clean any dirt from around base of spark plug.

3. Remove spark plug using a 13/16 in. spark plug socket

(not provided).

4. Inspect spark plug for damage, and clean with a wire

brush before reinstalling. If insulator is cracked or

chipped, spark plug should be replaced.

NOTE: If replacing, use the following recommended

plugs are Torch E7RTC is NGK BPR6HS.

5. Measure plug gap. The correct gap is 0.028 − 0.031 in.

To widen gap, if necessary, carefully bend the ground

(top) electrode. To lessen gap, gently tap ground

electrode on a hard surface.

6. Seat spark plug in position; thread in by hand to prevent

cross-threading.

7. Tighten with wrench to compress washer. If spark plug

is new, use 1/2 turn to compress washer appropriate

amount. If reusing old spark plug, use 1/8 to 1/4 turn for

proper washer compression.

NOTE: An improperly tightened spark plug will become

very hot and could damage the engine.

8. Reinstall spark plug boot.

MAINTAINING THE DRIVE GEAR

See figure 15.

To ensure smooth operation of wheels, the wheel assembly

should be cleaned before storage.

1. Remove the nut and wheel and set aside.

2. Remove dust cover, e-ring, washer, pins, and wheel

gear. Clean any dirt from these items and the end of

the drive shaft by wiping with a dry cloth. If necessary,

rubbing alcohol may be used to remove any stubborn

dirt.

WARNING

Do not lubricate any of the components of the wheel.

Lubrication may cause the wheel components to fail

during use, which could result in mower damage and/or

serious personal injury to the operator.

3. Reinstall wheel gear with the arrows facing the front

of the mower. Reinstall pins, washer, e-rings, and dust

cover.

4. Reinstall wheel and nut. Tighten nut to secure.

STORING THE PRODUCT

When storing the mower for 30 days or more:

■ If using fuel stabilizer, follow stabilizer manufacturer’s

directions to add stabilizer to petrol in fuel tank. Run

engine at least 10 minutes after adding stabilizer to

allow the stabilizer to reach the carburetor.

WARNING

Do not store the lawn mower with petrol in the tank

inside a building where fumes may reach an open flame

or spark.

■ If not using fuel stabilizer, allow the engine to run until

the mower is completely out of petrol.

■ Once the engine has stopped, allow the blade to come

to a complete stop and disconnect the spark plug wire.

■ Turn the fuel valve to the closed position.

■ Turn mower on its side (with carburetor facing up) and

clean grass clippings that have accumulated on the

underside of the mower deck.

■ Clean the underside of the mower deck.

■ Wipe the mower clean with a dry cloth.

■ Check all nuts, bolts, knobs, screws, fasteners, etc., for

tightness.

■ Inspect moving parts for damage, breakage, and wear.

Have repairs made on any damaged or missing parts.

■ Store the mower in a well-ventilated area that is clean,

dry, and out of the reach of children.

■ Do not store near corrosive materials such as fertilizer

or rock salt.

To lower the handle before storing:

■ Loosen the starter rope guide knob.

■ Fully loosen the handle knobs on the sides of the

handle and fold the upper handle down.

■ Unscrew the lower handle lock nuts.

■ Fold the lower handle forward, making sure not to bend

or kink the control cables.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15

Comentários a estes Manuais

Sem comentários

Models	Document Type
30G0339X2	Datasheet Lexmark 2x T650dtn, 8 pages
25A0249	Datasheet Lexmark C736dn, 6 pages
34S0330	Datasheet Lexmark E260dn, 4 pages
30G2051	Datasheet Lexmark T652dtn, 8 pages
25A0460	Datasheet Lexmark C734dn, 6 pages
24Z0000	Datasheet Lexmark C925de, 8 pages
14A1132	Datasheet Lexmark X560DN Color Laser Printer, 6 pages
21Z0180	Datasheet Lexmark C935DN, 4 pages
26B0000	Datasheet Lexmark C543DN, 6 pages
10Z0264	Datasheet Lexmark C782n, 6 pages
25C0383	Datasheet Lexmark C736dtn, 6 pages
25A0462	Datasheet Lexmark C736DTN, 6 pages
33S0115	Datasheet Lexmark E250d Laser, 2 pages
26C0141	Datasheet Lexmark C546DTN, 6 pages
33S0112	Datasheet Lexmark E250d Laser, 2 pages
26A0035	Datasheet Lexmark C543DN, 6 pages
13N1205	Datasheet Lexmark C920dtn, 4 pages
8049923	Datasheet Lexmark T650n, 8 pages
10Z0150	Datasheet Lexmark C780N, 5 pages
34S0312	Datasheet Lexmark E260DN, 4 pages

Ryobi RLM4619SME Manual do Operador Página 10

Comentários a estes Manuais

Lexmark 33S0101 manuals

Lexmark 33S0101 Datasheet (2 pages)

Table of contents

More products and manuals for Laser/LED printers Lexmark

Ryobi RLM4619SME Manual do Operador Página 10

Comentários a estes Manuais

Manuais e produtos relacionados com Corta-relvas Ryobi RLM4619SME

Lexmark 33S0101 manuals

Lexmark 33S0101 Datasheet (2 pages)

Table of contents

More products and manuals for Laser/LED printers Lexmark